Two marking gauge, includes:
1 x beech slitting gauge,
1 x fruit wood mortice and marking gauge, retains good points.

A nickel plated Stanley no. 95 butt gauge made in USA. Retains an estimated 95%+ of its nickel plating. Face is marked out in inches up to 2 inches long. Retains good length cutters.

A nickel plated butt gauge no. 95 made by Stanley. Retains an estimated 90%+ of its nickel plating. Face is marked out in inches up to 2 inches long. Butt gauge rod is marked 'Pat Apld for' Retains good length cutters.

A Stanley no. 95 butt gauge made in USA. Retains an estimated 50% of its nickel plating. Face is marked out in inches up to 2 inches long. Retains good length cutters. Body is marked with speckling of pitting.

Butt gauge no. 95 made by Stanley. Retains an estimated 80% of its nickel plating. Face is marked out in inches up to 2 inches long. Adjuster screw is marked 'Stanley Rule & Level Co, New Britain Conn USA. Also has a replacement slotted adjuster screw. Retains good length cutters.

An old butt gauge made by Goodell Tool Co, Pat Dec. 18. 1894. Body retains an estimated 50% of its nickel plating, retains good points.

Marking gauge no. 90 made by Stanley. Rod is marked out in inches up to 5 inch long. Retains 80% of its black japanning.

Rosewood mortice gauge with brass fittings made by Robinson Hall, Sheffield. This old mortice gauge has some marks and dents and is chamfered to one edge close to points through use.

An unusual brass stem mortise gauge with oak head. A well made and collectable mortise gauge. Retains very little of the original points around 1mm left.

A little used butt gauge no. 3940 made in USA by Craftsmen. This butt gauge retains an estimated 95% of its plating. Face is marked out in inches up to 2 inch long. Has seen little used and retains good length cutters.

An early Stanley no. 95 butt gauge, cast is marked 'B'. This old butt gauge retains an estimated 50% of its nickel plating. Face is marked out in inches up to 1 1/2 inch long. Retains good length cutters.

Three woodworking tools made by Robert Sorby. Includes:
1 x Robert Sorby rosewood mortise gauge with brass fittings, retains good points.
1 x 13mm Robert Sorby sash mortise chisel.
1 x Robert Sorby marking knife, has some staining to rear of blade.

An old marking gauge no. 98 made by Stanley. Rods are marked out in inches up to 5 inch long with marking wheel to one end and marking pin the opposite end of the rod. This of Stanley no. 98 marking gauge retains little of its nickel plating.

A Stanley no. 95 butt gauge made in USA. Retains an estimated 85% of its nickel plating. Face is marked out in inches up to 2 inchses long. Retains good length cutters.

Beech marking gauge no. 64 made by Stanley New Britain Conn USA. Has a boxwood thumb screw, marking gauge is marked out in inches up to 6". Pin has been replaced.

Butt gauge no. 93 made in USA by Stanley (sweetheart logo). This old butt gauge retains an estimated 90-95% of its finish.

Rosewood mortice and marking gauge with decorative brass fittings. Stem is marked out in inches up to 3" long. Retains good length points. Has previous woodworkers name stamp to head.

A fine Stanley no. 95 butt gauge made in USA. This old butt gauge retains an estimated 98% of its finish and comes complete with the original Stanley box (box is in poor condition, missing its label and tears to lid). Face of butt gauge is marked out in centimeters up to 5cm long. Retains good length cutters. Adjuster knob is marked Stanley made in USA.

Dual marking gauge made by Tyzack. Adjuster screws are marked 1989, Sheffield Eng plus the Tyzack logo. Brass body has little of the original finish remaining. Steel rods have 3 saw cuts.

A fine Stanley no. 95 butt gauge made in USA. This old butt gauge retains an estimated 99% of its finish and comes complete with the original Stanley box (has tears to corners of lid). Face is marked out in inches up to 2 inch long. Retains good length cutters.

A fine no. 95 butt marking gauge made in USA by Stanley. Face is marked out in inches up to 2 inch long. A fine butt gauge that retains an estimated 98% of its finish, comes complete with unnamed box.

A lovely old ebony slitting gauge with brass face and fittings. Head is very faintly marked Mitchell Eastbourne. This old ebony slitting gauge has a crack through the base that measures 75mm long. A lovely old collectable tool.

A Stanley Defiance butt gauge no. 1925, made in USA. This butt gauge face is marked out in inches up to 2 inch long. Retains good length cutters.

A mortice and marking gauge made by Marples, includes:
1 x rosewood mortice gauge with brass adjuster and fittings, marked Marples made in England.
1 x beech marking gauge with boxwood thumb screw made by Marples. Also marked with the ministry arrow and date of 1941. The pin has been replace to the opposite end of the beech rod.

A brass stem mortice gauge with ebony head, has a small chip to underside of head (10mm long). This old tool has a number of dents to the brass stem and head. Retains 3mm long sharp points.

An old rosewood mortice gauge with brass fittings made by W. Marples & Sons. Has some ware to top part of the stem. This collectable Mortice guage retains the original box marked Marples Tools Shamrock Brand, Wm Marples & Sons Ltd Hibernia Works, Sheffield, England, Warranted, also marked with the clover leaf logo.